Productos->Ethernet->Accesorios para PowerDAQ y PowerDNA->Accesorios PowerDNA | ||
Accesorios para PowerDNA |
||
DNA-19RACKW 19" rackmount enclosure with DIN rail attached. Holds up to 4 PowerDNA cubes (5- or 8-layer versions or any combination) |
||
DNA-5B-CONN 24-channel signal-conditioning mating panel for PowerDNA |
||
DNA-ACCESSORY I/O Cube accessories kit including power supply with cable, ethernet cable and debug cable./td> | ||
DNA-CASE Light-weight plastic carrying case for PowerDNA Cube. |
||
DNA-CBL-37 3ft, 37-way, male to female flat ribbon cable |
||
DNA-CBL-37HC 37-way male to female flat ribbon cable; connects DNA/DNR-DIO-470 with DNA-STP-37HC |
||
DNA-CBL-37S 37-way, male to female, round shielded cable with thumb screws. 3ft, 1ft, 10 ft or 20 ft length |
||
DNA-CBL-62 62-way, male to male, round shielded cable. 2.5ft, 10ft or 20ft length |
||
DNA-CBL-650 IRIG cable providing BNC connections for Clock/IRIG signals and 37-pin connections for other I/O |
||
DNA-CBL-COM 1ft, 4-port, round shielded cable. Can be used for CAN bus and serial communication PowerDNA layers. |
||
DNA-CBL-SYNC-10 Provides Cube to Cube synchronization via Sync ports |
||
PD-CBL-3737 Cube to Cube Synchronization Cable with male RJ Ethernet Connector on one end |
||
DNA-CONN37-DIR DB37 Male, direct-connect ribbon cable connector for PowerDNA I/O layers and mating panels. |
||
DNA-CONN37-RTA DB37 Male, right angle mount connector for PowerDNA I/O layers and mating panels. |
||
DNA-CONN37-STR DB37 Male, straight mount connector for PowerDNA I/O layers and mating panels. |
||
DNA-DIO-O22 The DNA-DIO-O22 is an external accessory panel for the DNA-DIO-403. Panel distributes 48 DIO channels, into 3 groups of 16 lines which connect to three Opto-22 compatible connectors. |
||
DNA-DR5 Rear-mount DIN rail clip for PowerDNA 5-layer Cube |
||
DNA-DR5U Universal DIN Rail Clip mount for 5-Layer DNA-PPC and DNA-PPC-1G family Cubes |
||
DNA-DR8 Rear-mount DIN rail clip for PowerDNA 8-layer Cube |
||
DNA-DR8U Universal DIN Rail Clip mount for 8-Layer DNA-PPC and DNA-PPC-1G family Cubes |
||
DNA-FAN5 Rear-mount fan for PowerDNA 5-layer Cube (except -1G versions) |
||
DNA-FAN8 Rear-mount fan for PowerDNA 8-layer Cube (except -1G Cubes). |
||
DNA-FLANGE Bottom-mount flange assembly for all versions of the Cube including PowerDNA, UEILogger, UEIPAC and UEIModbus. The flange assembly is the same for both sizes of cube. |
||
DNA-GPS GPS interface for PowerDNA, UEILogger, and UEIPAC |
||
DNA-PSU-24N +24V, 60 Watt external power supply |
||
DNA-SDXGB Ultra high-speed Secure Digital (SD) card; 2GB, 4GB, 8GB or 32GB capacity |
||
DNA-STP-207TC Screw terminal panel for the DNA-AI-207 and thermocouples. |
||
DNA-STP-37 37-way screw terminal panel |
||
DNA-STP-37HC 37-way screw terminal panel for use with DNA/DNR-DIO-470 |
||
DNA-STP-508 Breakout and interconnnection board for the DNx-SL-508 |
||
DNA-STP-62 62-channel screw terminal panel |
||
DNA-STP-AI-208 The DNA-STP-AI-208 is a direct-connect 8-channel terminal panel designed for strain gage measurements. DNA-STP-AI-208 supports Full- (4- and 6-wire schemes), Half- (3- and 4-wire schemes) and Quarter-Bridge (2- and 3-wire schemes) configurations. Quarter- and Half-Bridge configurations require user-populated bridge-completion resistors. This panel may be attached directly to the DNA-AI-208 strain gage data acquistion board or used with 37-way flat ribbon cable (DNA-CBL-37) as a desktop panel. |
||
DNA-STP-AI-U The DNA-STP-AI-U is a universal screw-terminal panel designed for PowerDNA DNA-AI-201-100 and DNA-AI-225 analog input data acquisition layers. |
||
DNA-STP-SYNC-1G Synchronization and Screw Terminal Panel for UEI DAQ Cubes |
||
DNR-EXT-BRACKET-4 The DNR-EXT-BRACKET-4 is designed to allow DNR-12, UEIPAC 1200R and UEISIM 1200R series RACKtangles to be installed �deeper� in 19� racks than the standard brackets provided with the units. The extended bracets provide a full 3.625 inch clearance between the front panel of the 19� rack and the front of the RACKtangle chassis. |
||
DNR-IO-FILLER The DNR-IO-FILLER is a blank/filler panel designed to be installed in unused RACKtangle slots. Though the filler is not required for operation, using filler panels in unused slots minimizes dust and contamination within the chassis and also ensures proper cooling air flow. |
||